How to price a 3D print in India: a formula and a worked example in rupees
Price an FDM print as material plus machine time, grossed up for failures, plus labour and overhead, then markup. Worked in rupees: a 62 g PLA part at ₹394.
Short answer
Price a 3D print from its costs: material plus machine time, divided by (1 minus your failure rate), plus the minutes you touch the job, plus a share of overheads, then add markup. With Indian prices on 21 November 2026, a 62 g PLA part that prints for 3 hours 20 minutes on a Bambu Lab P1S costs about ₹263 to make and sells for about ₹394 at a 50 percent markup, which is ₹6.35 a gram, inside the ₹5 to ₹10 a gram where most per-gram listings in IndiaMART’s FDM category sat that day.
Key takeaways
- Price = (material + machine time) ÷ (1 − failure rate) + labour + overhead, then × (1 + markup).
- PLA listed at ₹699 to ₹1,500 a kg at three Indian sellers on 21 November 2026, so filament is roughly ₹0.70 to ₹1.50 a gram.
- A Bambu Lab P1S averages 105 W printing PLA, per Bambu’s own measurements, so electricity is about ₹0.60 to ₹2 an hour; depreciation is the bigger machine cost.
- A 50 percent markup is a 33 percent margin. A 50 percent margin needs a 100 percent markup.
- On small single parts, labour and setup outweigh filament, which is what a minimum order value is for.
Price a 3D print from its costs, not from a guess at the market. Add material and machine time, divide by one minus your failure rate, add the minutes you actually spend on the job and a share of your overheads, then add markup. With Indian prices on 21 November 2026, a 62 g PLA part that prints for 3 hours 20 minutes on a Bambu Lab P1S costs about ₹263 to make and sells for ₹394 at a 50 percent markup. That is ₹6.35 a gram, inside the ₹5 to ₹10 a gram that most per-gram listings in IndiaMART’s FDM category asked that day.12
The formula, in one line:
Price = [ (material + machine time) ÷ (1 − failure rate) + labour + overhead ] × (1 + markup)
The rest of this page explains each term, works three jobs through in rupees, and shows where the shortcuts (a flat rate per gram, or per hour) lose money.
What costs go into a 3D print?
#Every FDM print (fused deposition modelling, the melted-filament kind) carries five costs:
- Material: the filament the slicer says the job uses, including supports and purge.
- Machine time: what an hour of the printer costs you, in wear, power and upkeep.
- Labour: the minutes a person spends on the job.
- Failures: the prints that do not ship, paid for by the ones that do.
- Overheads: rent, software, packing material and everything else that is not one job’s.
Shipping is a separate line, priced from the box. See shipping 3D printed parts in India.
How do I work out material cost per gram?
#Take the grams from the slicer, not the weight of the finished part. The slicer’s figure includes supports, brims and, on a multicolour job, the filament flushed at every colour change, all of which you bought.
Multiply by what a gram costs you. Here is what 1 kg spools cost from three Indian sellers on 21 November 2026:
| Seller | Filament | Listed price | Per gram |
|---|---|---|---|
| WOL3D | WOL3D PLA, pack of 12 × 1 kg (out of stock) | ₹14,4006 | ₹1.20 |
| WOL3D | Flashforge PLA, pack of 6 × 1 kg (out of stock) | ₹9,0006 | ₹1.50 |
| 3Idea | Bambu Lab PLA Basic refill, 1 kg | ₹1,1499 | ₹1.15 |
| 3Idea | 3Idea PLA+ HS, 1 kg | ₹8697 | ₹0.87 |
| 3Idea | 3Idea PLA+, 1 kg | ₹6998 | ₹0.70 |
| Robocraze | PLA, 1 kg (sold out on the day) | ₹96911 | ₹0.97 |
| 3Idea | PETG (3Idea, eSun), 1 kg | ₹869 to ₹1,29910, 7 | ₹0.87 to ₹1.30 |
| 3Idea | ABS (3Idea, eSun), 1 kg | ₹949 to ₹1,2577 | ₹0.95 to ₹1.26 |
So PLA was ₹699 to ₹1,500 a kg, and two of the six PLA listings could not be bought that day. Use your own last invoice, including what you paid for delivery. The examples below use ₹1.20 a gram.
How do I work out what an hour of printing costs in rupees?
#An hour of machine time is three numbers added together.
Depreciation. Divide what the printer cost by the hours you expect it to print. WOL3D listed the Bambu Lab P1S at ₹50,999 and the A1 at ₹29,999, both inclusive of taxes.4, 5 The life figure is the weak part. The commonly quoted 5,000 hours comes from vendor blogs such as Snapmaker’s,16 and QIDI’s own guide says plainly that “there is no published hour rating”.17 At 5,000 hours a P1S costs ₹10.20 an hour; at 3,000 hours it costs ₹17.00. Pick a figure, then correct it when your first machine is retired.
Power. Use measured averages, not the power supply rating. Bambu Lab’s wiki gives measured average draw while printing PLA of 105 W for the P1S and 95 W for the A1, and a steady-state 200 W for the P2S.1 The 1,000 W the same page lists for the P1S is its maximum power, a peak rating, not what it draws across a print.1
Your tariff is in your DISCOM’s tariff order, and within one state the rate can more than triple from the lowest slab to the highest.3 In Maharashtra, MERC’s order of 25 March 2026 sets these variable charges for MSEDCL from 1 April 2026:2, 3
| MSEDCL category (FY 2026-27) | ₹ per kWh | P1S power cost per hour |
|---|---|---|
| Residential, 1 to 100 units | 5.563 | ₹0.58 |
| Residential, 101 to 300 units | 12.403 | ₹1.30 |
| Residential, above 500 units | 19.133 | ₹2.01 |
| Non-residential, up to 20 kW | 10.113 | ₹1.06 |
Those are energy plus wheeling charges; fixed charges, fuel adjustment and electricity duty come on top.3 Find your own category on your bill and the rate in your state commission’s current order. Either way, power is a small line next to depreciation.
Maintenance. Nozzles, build plates, belts and lubricant. Without your own records, put in an assumption and replace it. We use ₹2 an hour (₹5,000 a year over 2,500 printing hours).
For a P1S on a residential 101 to 300 unit slab: ₹10.20 + ₹1.30 + ₹2.00 = ₹13.50 an hour.
How much labour do I charge for, and why not the print hours?
#Charge for the minutes a person touches the job: checking the file, slicing, starting the plate, removing supports, inspecting, packing and answering messages. The hours the printer runs unattended are already paid for in the machine rate. Charging labour for them as well would double count.
Choose what your hour is worth; we use ₹300 as a placeholder, not a market rate. Time your next ten jobs.
How do I allow for failed prints?
#Divide material and machine cost by (1 − failure rate). Dividing is right and adding a percentage is slightly short: if 1 print in 10 fails, nine good prints carry the cost of ten, which is ÷ 0.9 (an extra 11.1 percent), not × 1.1. Snapmaker’s guide uses the same arithmetic.16
Start with 10 percent as an assumption, then replace it with the rate from your own log. Failed prints, purge and supports covers how to measure it.
Markup or margin: what is the difference?
#Both add profit, from different ends.
- Markup is profit as a share of cost: price = cost × (1 + markup).
- Margin is profit as a share of price: price = cost ÷ (1 − margin).
On a cost of ₹262.67, a 50 percent markup gives ₹394.00, which is a 33.3 percent margin. A 50 percent margin gives ₹525.33, which is a 100 percent markup. Say which one you mean when you set a target, or you will be ₹131 apart on one small part.
Worked example: one part, a batch of twenty, a multicolour part
#Assumptions: Bambu Lab P1S at ₹13.50 an hour, PLA at ₹1.20 a gram, 10 percent failures, labour at ₹300 an hour, overhead of ₹30 an order (₹6,000 a month of fixed costs over 200 orders), markup of 50 percent. Grams and hours are illustrative figures of the kind a slicer reports, not measurements.
| One part | Batch of 20 | Multicolour part | |
|---|---|---|---|
| Grams from slicer | 62 g | 1,240 g (4 plates of 5) | 110 g (62 g part + 48 g flush) |
| Print time | 3 h 20 min | 60 h | 5 h 30 min |
| Material | ₹74.40 | ₹1,488.00 | ₹132.00 |
| Machine time | ₹45.00 | ₹810.00 | ₹74.25 |
| Failure allowance (÷ 0.9) | ₹13.27 | ₹255.33 | ₹22.92 |
| Labour | 20 min, ₹100.00 | 115 min, ₹575.00 | 25 min, ₹125.00 |
| Overhead | ₹30.00 | ₹30.00 | ₹30.00 |
| Cost | ₹262.67 | ₹3,158.33 | ₹384.17 |
| Price at 50% markup | ₹394.00 | ₹4,737.50 | ₹576.25 |
| Per part | ₹394.00 | ₹236.88 | ₹576.25 |
| Per gram of finished part | ₹6.35 | ₹3.82 | ₹9.29 |
Three things fall out of the table.
- On the single part, labour is the biggest line. ₹100 of time against ₹74 of plastic.
- The batch is cheaper per part because file checks, packing and overhead are paid once. ₹3.82 a gram is below most listed rates, and it is still a 50 percent markup on cost.
- The multicolour part costs 46 percent more than the same part in one colour, mostly from flush waste and the extra time colour changes take. A per-gram price on the finished part would never see it. If you bought an AMS for multicolour work, add its price to the printer before you work out depreciation: WOL3D listed the P1S Combo, which includes one, at ₹68,999,4 which is ₹13.80 an hour over 5,000 hours instead of ₹10.20. The table uses the plain P1S rate; at the Combo rate this part’s price rises by about ₹33.
Per gram or per hour: which should I quote?
#Each shortcut loses money on one shape of job. Take the single part’s rates, ₹6.35 a gram and ₹118 an hour, and try them on two other parts:
- A tall, light part: 40 g, 9 hours. Per gram it prices at ₹254, but it costs ₹318.33 to make. Per gram loses.
- A heavy, fast part: 400 g, 6 hours. Per hour it prices at ₹708, but it costs ₹753.33. Per hour loses.
Quoting the larger of the two figures covers cost on both of these parts, but it is not a guarantee: on a very small job, say 5 g and 30 minutes, the two rates give ₹32 and ₹59 while the fixed handling alone costs ₹130. And it can overprice badly: the tall part would go out at ₹1,062 when the formula gives ₹477.50. The formula has grams and hours in it already, so use it, and keep a spreadsheet with your rates filled in so a quote takes a minute. How to quote a custom 3D printing order covers what to ask before you price.
What minimum order value should I set?
#A minimum order value has to cover the cost of handling one order before any plastic is printed: the file check, the plate start and clear, packing, messages and the order’s overhead. In the example that is 20 minutes (₹100) plus ₹30, which is ₹195 with markup. Add the material and machine time of the smallest part you would accept and the floor lands at roughly ₹200 to ₹250 on these assumptions.
Some Indian services advertise no minimum order at all, Think Robotics and IamRapid among them (both checked on 21 November 2026), and quote each job instead;15, 14 IamRapid’s cost guide says its FDM parts start from ₹200.14 Quoting every job works when the quote includes your handling time. If it does not, a minimum is the simpler way to charge for it.
How does my price compare with market rates in India?
#Check against the market after you have a cost, not before. On IndiaMART’s FDM category on 21 November 2026, per-gram rates ran from ₹3.80 to ₹150, with most listings between ₹5 and ₹10.12 IamRapid lists FDM PLA from ₹6 a gram, before the GST its quotes add on top.13 These are asking prices that rarely say whether supports, finishing, GST or shipping are included.
If your price is far from the market, check your labour minutes, failure rate and printer life before you touch the markup.
Does the UPI fee change the price?
#Not yet, and when it starts, only slightly and only above ₹2,000. NPCI announced a 0.4 percent merchant discount rate on eligible merchant UPI payments above ₹2,000, capped at ₹300 (reached at ₹75,000), according to reporting on NPCI’s framework by Kotak Neo and Inc42.18, 19 It was due on 15 October 2026, but on 13 October NPCI deferred it to a date after Diwali “to be notified separately”, and no date had been notified by 21 November 2026.20, 21 Payments of ₹2,000 or less stay at zero, and small merchants whose monthly UPI QR collections stay below ₹1 lakh remain at zero.18, 19 The fee is charged to the merchant, not the customer,18, 19 so once it starts, treat it as a cost of the sale. If it applies to you then, the ₹4,737.50 batch order carries about ₹19 of fees.
What changes if I am GST-registered?
#This is general information; confirm your position with a chartered accountant.
If you are not registered, you cannot charge GST. Section 32 of the CGST Act bars an unregistered person from collecting any amount by way of tax,22 and the GST Council’s registration flyer notes that without registration you can neither collect tax nor claim input tax credit.24 Your price is the whole price, and the GST inside your filament and printer bills is a cost, which is why the examples above use tax-inclusive prices.
The composition scheme works the same way for pricing: Section 10(4) of the CGST Act says a composition taxpayer cannot collect tax from the customer or take input tax credit,23 so cost your inputs with GST included.
If you are registered under the regular scheme, you add GST on top of your price at the rate for what you supply, and you can usually claim credit for GST on your inputs, so cost them without it. Which rate and which HSN or SAC code apply depends on whether you are selling goods or a printing service; see GST and HSN/SAC codes for 3D printing in India. Either way, say in every quote whether GST is included.
After the job: did the quote match the cost?
#The inputs to the formula drift. After each job, compare the grams and hours you quoted with what the job used, including reprints. If you quoted 62 g and the spool lost 90 g, your failure rate or your purge figure is wrong, and every quote built on it is too. Weighing spools is the reliable way to know; see tracking filament by weight.
Where PrintFarmer fits
#PrintFarmer has no price calculator, so the price still comes from your formula; you can then issue it to the customer as a quote document. Where it helps is afterwards. An expense can be linked to an order for job costing, and recording a plate’s result prefills the grams it used, with wastage recorded apart from usage. That leaves a record of what each plate actually used and wasted, which you can set against the grams you quoted to see whether your formula needs new numbers. Tell us you’re interested. It is not launched yet.
Frequently asked questions
How much should I charge for a 3D print in India?
Work it out from your costs: material, machine hours, failures, the minutes you spend on the job and a share of overheads, then add markup. In our worked example a 62 g PLA part costs ₹263 to make and sells for ₹394 at a 50 percent markup.
What is the going rate per gram for PLA 3D printing in India?
On IndiaMART’s FDM category on 21 November 2026, most per-gram listings asked ₹5 to ₹10 a gram, with the full spread running from ₹3.80 to ₹150. Those are asking prices that rarely say what they include, so use them as a check, not as your price.
Should I price 3D prints per gram or per hour?
Neither alone. Per-gram pricing loses money on slow, light parts and per-hour pricing loses money on heavy, fast ones. Use a formula with both grams and hours in it, plus a fixed amount per job for the time you spend handling it.
What markup should a small 3D printing business add?
There is no standard figure. Pick a target margin, convert it to a markup with markup = margin ÷ (1 − margin), and check the result against market rates and against what your customers accept.
What minimum order value should a 3D printing service set?
At least the fixed cost of handling one order, marked up: the minutes spent checking the file, starting and clearing the plate, packing and messaging, plus your per-order overhead. In our example that is about ₹200 before any plastic is printed.
Do I add GST on top of my 3D printing price?
Only if you are GST-registered under the regular scheme. An unregistered seller, or one on the composition scheme, cannot collect GST from a customer, so their price is the whole price, and the GST they paid on filament is a cost they cannot claim back.
Sources
All sources accessed .
- Bambu Lab Wiki: Power consumption wiki.bambulab.com.
- MSEDCL tariff details (list of MERC tariff orders) mahadiscom.in.
- MERC order in Case No. 75 of 2025, dated 25 March 2026 (MSEDCL tariff, Annexure II) mahadiscom.in.
- WOL3D: Bambu Lab P1S 3D Printer (with the P1S Combo listing on the same page) wol3d.com.
- WOL3D: Bambu Lab A1 3D Printer wol3d.com.
- WOL3D: Flashforge PLA 1 kg multipack (with WOL3D PLA 12-pack listing) wol3d.com.
- 3Idea: 3D printer filaments category 3idea.in.
- 3Idea: 3Idea PLA+ Sky Blue 1.75 mm, 1 kg 3idea.in.
- 3Idea: Bambu Lab PLA Basic refill, 1 kg 3idea.in.
- 3Idea: PETG Sky Blue 1.75 mm, 1 kg 3idea.in.
- Robocraze: 1.75 mm Sky Blue PLA filament, 1 kg robocraze.com.
- IndiaMART: FDM 3D printing service listings m.indiamart.com.
- IamRapid: Pricing iamrapid.com.
- IamRapid: 3D printing cost guide iamrapid.com.
- Think Robotics: 3D printing services thinkrobotics.com.
- Snapmaker: How to calculate your 3D printing costs snapmaker.com.
- QIDI: How long does a 3D printer last? qidi3d.com.
- Kotak Neo: UPI MDR from October 15, exemptions kotakneo.com.
- Inc42: UPI MDR regime explained inc42.com.
- NPCI defers levy of MDR on UPI transactions; no new date announced for implementation (PTI via ThePrint, 13 October 2026) theprint.in.
- UPI MDR rollout may be delayed until 2027 elections as distributors seek exemption from charges (Business Today, 19 November 2026) businesstoday.in.
- CGST Act 2017, Section 32: Prohibition of unauthorised collection of tax knowyourgst.com.
- CGST Act 2017, Section 10: Composition levy knowyourgst.com.
- GST Council: Registration under GST Law (flyer) gstcouncil.gov.in.