PrintFarmer ERP
Tell us you’re interested

Tracking filament by weight: tare weights, stocktakes and knowing what is left on a spool

Weigh the spool, subtract the empty spool’s weight, and record every gram as a movement. Tare weights by brand, a stocktake method and grams to metres.

Short answer

To know what is left on a spool, weigh it and subtract the weight of the empty spool (the tare): a spool that reads 652 g on the scale, with an empty-spool weight of 154 g, holds 498 g of filament. To track a whole shop, give each spool an ID and record every gram in or out as a dated movement (received, used, wasted, adjusted) instead of overwriting a total, then weigh open spools regularly and record the difference as an adjustment.

Key takeaways

  • Filament left = gross weight on the scale minus the empty-spool (tare) weight. Nothing else is needed.
  • Empty spools for 1 kg of filament weigh roughly 120 g to 280 g depending on brand and spool material, so a single guessed figure can be wrong by more than 100 g.
  • Record movements, not totals: a balance is the sum of received, used, wasted and adjusted grams, so you can always see where stock went.
  • 1 kg of 1.75 mm PLA at 1.24 g/cm³ is about 335 m; 1 m of it weighs about 3 g.
  • Check stock against accepted orders by material and colour, and against the largest single spool, before promising a date.

To know how much filament is left on a spool, put it on a scale and subtract the weight of the empty spool. That empty weight is called the tare. A spool that reads 652 g on the scale, with a tare of 154 g, holds 498 g of filament. To track a whole shop, do that for every spool, give each spool an ID, and write down every gram that comes in or goes out as a dated line instead of overwriting a running total.

Below is how to do that cheaply, and how to answer the question that costs money: do you have enough of the right colour for the orders you have already accepted?

What three numbers do you need for each spool?

#
  1. Net weight on the label, usually 1,000 g. This is what you paid for.
  2. Tare, the weight of the empty spool, including any cardboard core.
  3. Gross weight, what the scale says today.

Filament left = gross − tare.

Net weight on the label is nominal. We could not find a manufacturer that publishes a tolerance on it, so treat 1,000 g as what you paid for, and let the first weighing tell you what you got.

A kitchen scale is enough. Common models read up to 5 kg in 1 g steps (the Beurer KS 19, for example).14

How much does an empty filament spool weigh?

#

It depends on the brand and on whether the spool is plastic or cardboard, and few manufacturers publish it. The table uses the manufacturer’s figure where one is published, and otherwise SpoolmanDB, a community-maintained database of filaments that the open-source Spoolman tracker draws on.2 Figures were checked on 21 November 2026.

Brand and spool (1 kg, 1.75 mm) Empty spool, approx. Where the figure comes from
Elegoo PLA 154 g ±10 g1 Elegoo product page
Bambu Lab reusable spool (plastic) 250 g4, 3 Retailer specification and SpoolmanDB; forum users weighed 245 g to 255 g depending on spool colour, including a 37 g to 38 g cardboard core5
eSun PLA and PLA+ (cardboard) 170 g3 SpoolmanDB
eSun PETG, ABS+, TPU 95A 240 g3 SpoolmanDB
Sunlu PLA, PLA+, PETG (plastic) 189 g3 SpoolmanDB
Polymaker (cardboard) 140 g3 SpoolmanDB
Creality PLA 120 g3 SpoolmanDB
Creality PETG (plastic) 225 g3 SpoolmanDB
Prusament (plastic) 193 g or 278 g, by spool type3 SpoolmanDB
Overture (cardboard) 132 g to 174 g, by product line3 SpoolmanDB
Numakers PLA, PLA+, PETG 200 g3 SpoolmanDB
Numakers ABS, ASA 260 g3 SpoolmanDB
WOL3D Not published Weigh an empty spool

Read these as starting points: Elegoo’s own figure carries ±10 g,1 and spools of one brand differ by colour and product line. The spread in the table, from 120 g to 278 g, is the reason a single “spools weigh about 200 g” rule fails: it is wrong by up to 80 g in either direction.

How do I find the tare when I have no empty spool?

#
  • Look at the label and the box first. Some brands print it.
  • Use the table above as a provisional figure and mark it as provisional.
  • When the first spool of that brand and type runs out, weigh the empty spool and replace the provisional figure. That one weighing corrects every future spool of the same kind.

Give each spool an ID

#

Give every spool its own ID (S-041, S-042) the day it arrives, and put the ID on the spool itself, not the box. A sticker on the flange survives being moved between printers and dry boxes. Two spools of the same black are two records: when two printers draw from them at once, one total for “black” is true of neither.

Record movements, not totals

#

A movement is one dated line that changes stock: received, used, wasted, or adjusted. The balance of a spool is the sum of its movements. Nobody types the balance in.

Date Spool Type Grams Against By
3 Nov S-041 Received +1,000 Supplier invoice Asha
6 Nov S-041 Used −212 Order 1182, plate 3 Ravi
9 Nov S-041 Used −148 Order 1190 Ravi
11 Nov S-041 Wasted −31 Plate 7 failed at 40% Ravi
14 Nov S-041 Used −96 Order 1201 Asha

Book balance: 1,000 − 212 − 148 − 31 − 96 = 513 g.

Why does overwriting the total lose information?

#

A spool overwritten from 1,000 g to 640 g cannot say where the 360 g went, whether into orders or the bin, who changed it, or why the shelf disagrees with the sheet. A movement list answers all of those, and a mistake is corrected by adding a line, not by an edit that erases the old one.

Should failed prints and purge count as usage?

#

They reduce stock, so they must be recorded. Record them as wastage, separate from usage. Usage is filament that left in a parcel. Wastage is filament that did not: failed plates, purge and colour-change flushes, test prints, and the tail end you cut off. Kept apart, the two give you a waste percentage you can price into quotes. Costing failed prints and purge covers turning that into rupees.

How do I do a filament stocktake?

#

A stocktake compares what the records say with what is physically there. With tares on file, it is weighing, not counting.

  1. Pull every open spool from printers, dry boxes and shelves onto one table.
  2. Weigh each one and write the gross weight next to its ID.
  3. Subtract the tare to get the actual grams.
  4. Compare with the book balance.
  5. Record the difference as an adjustment movement with a reason. Do not edit old lines.
  6. Count sealed spools without weighing them; they are still at their received weight.

Expect twenty open spools to take roughly twenty minutes, most of it fetching spools.

Worked example

#

S-041 is Elegoo PLA, tare 154 g.1 The book balance is 513 g. The scale reads 652 g, so the spool holds 652 − 154 = 498 g. The adjustment is 498 − 513 = −15 g.

Assume filament costs ₹1.20 a gram, the figure used in how to price 3D prints in India. The unexplained 15 g is worth ₹18. Small, but note two things. First, Elegoo’s tare tolerance alone is ±10 g,1 so part of the difference may be the spool, not the records; weighing the empty spool at the end settles it. Second, if every spool is 15 g short, something is going unrecorded, usually purge or a failed plate nobody logged.

How often should a print farm do a stocktake?

#

There is no standard interval. A workable rhythm: weigh a spool every time it comes off a printer, which costs ten seconds, and weigh every open spool on a fixed day each week or month depending on volume. The aim is that every difference is recent enough that someone remembers its cause.

Slicer estimate versus the scale: where does the difference go?

#

The slicer’s figure is what the file should use. The scale is what was used. The gap usually comes from purge and flushing (counted differently by different slicers and settings), filament cut off when loading, failed or restarted prints, and test pieces. When usage is recorded from the slicer estimate, the stocktake adjustment is where all of this shows up. Recording failures as wastage when they happen shrinks the adjustment to genuine unknowns.

Printer-side estimates have the same limit. As of November 2026, Bambu Lab’s wiki says the AMS estimates the remaining percentage from how much filament is fed while the RFID tag on a Bambu spool turns one full circle, with a full 1 kg roll counted as 100% by default.11 That is an estimate for that spool in that printer, not a stock record. SimplyPrint’s Filament Manager deducts estimated usage when a print ends, but its help article says prints must be started through SimplyPrint to be tracked; prints from USB, an SD card or the printer’s screen are not.12

How do I convert filament grams to metres?

#

Length = mass ÷ (density × cross-sectional area).

For 1.75 mm filament the cross-section is π × 0.875² ≈ 2.405 mm². Densities below are from manufacturer data sheets (ISO 1183).

Material Density (g/cm³) Metres per kg Grams per metre
PLA (Bambu PLA Basic) 1.246 335 2.98
PETG (Bambu PETG Basic) 1.257 333 3.01
ABS (Bambu ABS) 1.059 396 2.53
TPU (Bambu TPU 95A) 1.208 347 2.89

Check for PLA: 1,000 g ÷ 1.24 g/cm³ = 806.5 cm³ = 806,452 mm³. Divided by 2.405 mm² gives 335,300 mm, or about 335 m. For PLA, 100 g is about 33.5 m and 500 g about 168 m. Other brands’ densities differ by a few hundredths, which moves these figures by a few per cent (Polymaker’s PolyLite ABS sheet gives 1.04, for example)10, so use your own brand’s data sheet if it matters.

Do I have enough filament for the orders I have accepted?

#

Add up what accepted, unprinted work will need, by material and colour, and compare it with what is on hand.

Material and colour Needed by accepted orders On hand Result
PLA Matte Black 50 keychains × 9 g + 3 parts × 120 g = 810 g S-041 498 g + S-052 sealed 1,000 g = 1,498 g Covered
PLA Silk Red 620 g 410 g Short by 210 g

Two checks people miss:

  • Add your waste rate. If your wastage runs at 5% (an assumption; use your own figure), 810 g needs about 851 g.
  • Compare the largest plate with the fullest open spool. If one plate needs 600 g, it cannot print from a 498 g spool without a swap mid-print, even when the colour’s total looks fine.

Do this when you accept the order, not when you load the printer. Organising a print queue across several printers covers turning those orders into plates.

When should I reorder a colour?

#

A reorder point is the balance at which you order more. A simple version is average daily use × (supplier lead time + safety days).

Assume black averages 250 g a day over the last thirty days, a delivery takes five days, and you want three days of cover. The reorder point is 250 × (5 + 3) = 2,000 g. When open plus sealed black drops below two spools, order. The movement list gives you the daily average directly; a total that gets overwritten cannot.

A spreadsheet layout that works for one person

#

Two sheets.

  • Spools: spool ID, material, colour, brand, supplier, received date, cost, net weight, tare, whether the tare is provisional.
  • Movements: date, spool ID, type (received, used, wasted, adjusted), grams (positive in, negative out), order or plate, who, note.

The balance per spool is a SUMIF over the movements sheet. Never type a balance.

Where does a shared spreadsheet break?

#

A shared sheet breaks on concurrent edits and on overwrites. In a Bambu Lab forum thread on filament stock sheets (November 2025), one user wrote “I’m afraid someone has saved over the file, and now a lot of info has disappeared”, and another set theirs to read-only “because people keep overwriting the file for others.”13 A sheet also cannot stop someone typing over a balance, does not know which orders are accepted, and does not record who changed what unless everyone remembers to fill that column.

Where PrintFarmer fits

#

PrintFarmer keeps stock as a movement ledger: on-hand is the sum of the movements and is never stored or set. Each spool carries its tare, so a stocktake is a scale reading and the difference is recorded as an adjustment. Wastage is recorded apart from usage. When someone records a plate’s result, the grams used and wasted are offered prefilled from the parts’ estimates, to be checked and saved by that person. It reports the shortfall against orders already accepted, by material and colour. Printable QR stickers on spools open a scan page on a phone. Magnets, split rings and mailers sit in the same ledger.

It is not connected to printers. It does not read AMS or RFID data and does not deduct filament automatically when a print runs; a person records what happened. For how it sits next to printer-side tools, see how print farm tools compare. Tell us you’re interested. It is not launched yet.

Frequently asked questions

How do I know how much filament is left on a spool?

Weigh the spool on a kitchen scale and subtract the weight of the empty spool. If you do not know the empty weight, use the manufacturer’s figure if it publishes one, or weigh an empty spool of the same brand and type.

How much does an empty 1 kg filament spool weigh?

Between about 120 g and 280 g. Elegoo publishes 154 g ±10 g for its 1 kg PLA spool, a retailer lists the Bambu Lab reusable spool at 250 g, and the SpoolmanDB community database puts cardboard spools from several brands at about 130 g to 175 g.

How do I convert filament grams to metres?

Length = mass ÷ (density × cross-sectional area). For 1.75 mm filament the area is about 2.405 mm², so 1 kg of PLA at 1.24 g/cm³ is about 335 m, and 1 g is about 0.34 m.

Should failed prints and purge be counted as filament usage?

Count them, but as wastage, recorded separately from usage on a sale. Both reduce stock; keeping them apart shows how much filament never shipped and what it cost.

How often should a print farm do a filament stocktake?

Weigh a spool whenever it comes off a printer, and do a full count of every open spool on a fixed day, weekly or monthly depending on volume. The aim is that no difference is old enough to have forgotten its cause.

What columns does a filament inventory spreadsheet need?

A spools sheet with spool ID, material, colour, brand, supplier, cost, net weight and tare, and a separate movements sheet with date, spool ID, type, grams, order or plate, and who recorded it. The balance is the sum of the movements.

Sources

All sources accessed .

  1. ELEGOO PLA Filament 1.75mm Colored 1KG (product page, empty spool weight) elegoo.com.
  2. SpoolmanDB: community database of filaments and spool weights (repository) github.com.
  3. SpoolmanDB compiled data (filaments.json) donkie.github.io.
  4. Bambu Lab Reusable Spool (retailer specification, 3D Universe) shop3duniverse.com.
  5. Why don’t you put the weight of the spool on each roll? (Bambu Lab forum) forum.bambulab.com.
  6. Bambu PLA Basic Technical Data Sheet cdn.shopify.com.
  7. Bambu PETG Basic Technical Data Sheet cdn.shopify.com.
  8. Bambu TPU 95A Technical Data Sheet cdn.shopify.com.
  9. Bambu ABS Technical Data Sheet V3 store.bblcdn.com.
  10. PolyLite ABS Technical Data Sheet V5.4 (Polymaker) cdn.shopify.com.
  11. AMS Function Introduction: Remaining Filament Estimation (Bambu Lab Wiki) wiki.bambulab.com.
  12. The Filament Manager feature (SimplyPrint Help) help.simplyprint.io.
  13. Filament stock tracking (Excel) (Bambu Lab forum thread) forum.bambulab.com.
  14. Beurer KS 19 kitchen scale (technical specifications) beurer.com.

Run one real order through it

PrintFarmer is an ERP for 3D print shops. The enquiry, the quote, the plates, the parcel, the invoice and the payment sit on one record, so the answer is on the screen and not in a chat thread.